Technology explained
How a Radar Chronograph Works (and Why It Misses Shots)
A lot of shooters assume a radar chronograph is triggered by the bang. In fact it's watching for a tiny change in the frequency of radio waves bouncing off the bullet. That's why suppressors, muzzle brakes and bad light make no difference to it, and why the way it's pointing matters a great deal.
Understanding that one idea explains almost every missed shot. If you just want the step-by-step fixes, our chronograph setup guide has them. This article explains why they work.
The Doppler effect, at the bench
You've heard the Doppler effect: a ute's engine note drops as it passes you. Radio waves do the same thing. The chronograph sends out a radio signal, and a bullet flying away reflects a little of it back. Because the bullet is moving away, the echo comes back stretched to a slightly lower frequency. The faster the bullet, the bigger the stretch. The diagram below shows the idea.
Garmin's manual lists the Xero C2's radar band as 24.15 to 24.25 GHz. By our calculation, a bullet at 2,800 fps shifts a 24.2 GHz signal by roughly 137.8 kHz, and every extra 10 fps adds about 0.49 kHz. Measuring a shift that small precisely is how a pocket-sized unit reaches Garmin's rated rifle accuracy of ±0.1%.
Garmin also says an algorithm in the Xero units works out true muzzle velocity with no manual position offset. So you simply place the unit within the recommended range, with no distance to enter.
How radar compares with the older methods
Radar is one of three common ways to measure velocity. The two older approaches still work, but each has a trade-off radar avoids, as the comparison below shows.
Light screens time the bullet between two sensors you shoot over, so they need decent light and careful aiming, and a misjudged shot can destroy one. Barrel-mounted units sit on the muzzle end of the barrel, which adds weight there and can move your point of impact. Garmin makes the point directly for its own units: because nothing attaches to the firearm, they don't affect your zero or barrel harmonics.
Why a radar unit misses shots
Picture a frosty July morning. You set up before sunrise, nudge the chronograph while settling the rifle on the bags, and your cold-bore shot doesn't register. The second shot, after you straighten it, reads fine. The unit is fine; the bullet simply flew outside the area the beam was covering.
The radar signal spreads out from the large flat face towards the target. Point that face at the target and the bullet flies straight down the middle. Turn it away, or set it too far out to the side, and the bullet crosses the edge of the beam or misses it, leaving too little echo for a clean reading. That's why Garmin's first troubleshooting check is the unit's orientation, and why both brands give tight spacing ranges.
The other causes follow from the same principle. Garmin asks for at least 20 m of clear flight path, and we'd expect that's because the unit needs to follow the bullet for a short stretch to measure it well. A neighbour's bullet crossing the beam produces its own echo, hence the advice to keep shooters 1.5 m apart, and the Athlon Velocity Pro's claim to pick out your bullet. And each echo takes processing time, which is why the Xero C2 publishes a maximum of 10 rifle shots a second.
Garmin's units also check for other radars when a session starts and switch to a clean channel automatically, so two radar chronographs on the same line can work side by side.
Once readings are coming in reliably, the next question is what they mean. Our guide to SD and ES covers that, and our radar chronograph comparison covers which unit to buy.
Radar Chronograph FAQ: How It Works
How does a radar chronograph work?
A radar chronograph sends out a radio signal and measures the echo reflected by the moving bullet. Because the bullet is travelling away, the echo returns at a slightly lower frequency, an effect called Doppler shift. The size of that shift is proportional to the bullet's speed, so the unit can calculate velocity without being triggered by muzzle blast or attached to the firearm.
What frequency does a Garmin Xero chronograph use?
Garmin's Xero C2 manual lists its radar transmitting in the 24.15 to 24.25 GHz band at under 20 dBm, alongside a 2.4 GHz band for Bluetooth. The earlier Xero C1 manual lists 24 GHz radar. By our calculation, a 2,800 fps bullet shifts a 24.2 GHz signal by about 137.8 kHz.
Is a radar chronograph better than an optical chronograph?
For most shooters, yes. A radar chronograph sits beside the firearm, isn't affected by lighting, and doesn't need you to shoot over sensors that a stray shot could hit. Optical light-screen units can be accurate and cost less, but setup takes longer and they depend on reasonable light. Radar units also cope with suppressors and muzzle brakes.
Does a barrel-mounted chronograph affect accuracy?
It can. Anything attached to the muzzle end of the barrel adds weight there, which can shift point of impact compared with shooting without it. That's one reason radar chronographs have become popular: Garmin notes that because nothing attaches to the firearm, its Xero units don't affect your zero or barrel harmonics.
Why does a radar chronograph need 20 m in front of it?
Garmin's manuals ask for at least 20 m of clear flight path in front of the Xero chronograph for reliable readings. Garmin doesn't explain the reason, but we'd expect it's because the radar needs to follow the bullet over a short stretch to measure the Doppler shift well. For archery, Garmin's minimum target distance is 4 m.
Does a radar chronograph work in low light or indoors?
Yes. Radar measures the reflected radio signal, not light, so a dull morning or an indoor range doesn't affect the reading the way it can with optical light screens. Garmin says its Xero units work indoors and outdoors and have a backlit display. Indoor ranges still need enough length for the 20 m flight path Garmin recommends.
Can two radar chronographs be used side by side?
Generally, yes. Garmin's Xero C1 and C2 manuals say the unit checks for interference from other radar systems when a session starts and switches to a clean channel automatically. Separately, keep the nearest shooter at least 1.5 m away, because a radar chronograph can also pick up the bullets from an adjacent firing point.
Can a radar chronograph measure velocity downrange?
Garmin's Xero units have a downrange mode for when the chronograph is placed away from the firing line to track velocity at that point. The screen flashes five times each time it detects a shot, so you can see detections from a distance. Garmin warns to follow your range's safety protocols when placing or adjusting a unit downrange.
Why don't I need to enter the chronograph's distance from the muzzle?
Garmin says the Xero C2 uses an algorithm that measures true muzzle velocity without a manual position offset, and the Xero C1 manual says the same. You simply place the unit within the recommended range, 15 to 35 cm beside the rifle and 15 to 35 cm behind the muzzle, and it handles the rest.
Radio frequencies and placement guidance come from Garmin's Xero owner's manuals; the Doppler shift figures are our own calculation.