Technology explained
How Far Can a Pulsar Telos Identify a Fox, Pig or Deer?
Most buyers read the 2,300 m on a Telos box as how far they'll see a fox. It isn't. That figure is the distance at which a 1.8 m by 0.5 m heat source covers about three pixels, enough to notice something is there. By our estimate, the higher-resolution Telos models identify a fox at around 170 m and recognise it as a fox-sized animal at around 340 m, with pigs and deer considerably further.
Those numbers are deliberately conservative, and the way we got them is below, so you can judge them for yourself. For choosing a model overall, start with our Pulsar Telos buyer's guide.
What the detection figure really means
Pulsar states that its detection range is measured against a standard 1.8 × 0.5 m target. We worked out how many pixels that target covers at each model's rated distance. The answer is the same story across the range, as the diagram below shows.
Three warm pixels tell you there's a heat source. They won't tell you whether it's a pig, a calf or a warm stump. Detection range is a fair way to compare models, but it was never meant to tell you when you can make a decision.
How we estimated identification
We used the Johnson criteria, the long-standing rule of thumb for thermal and night vision. In the commonly used form, you need about 1.5 pixels across a target to detect it, 6 to recognise what kind of thing it is, and 12 to identify it. We measured across each animal's characteristic size, the square root of its length times its height, using typical sizes: a fox about 0.7 × 0.35 m, a pig about 1.2 × 0.7 m and a deer about 1.5 × 0.9 m.
The pixel size on the ground depends only on the sensor's pixel pitch and the lens focal length. That gives three groups in the Telos range, shown in the table below.
| Telos model | Fox: recognise / identify | Pig: recognise / identify | Deer: recognise / identify |
|---|---|---|---|
| XG50, XL50, LRF XT50 (12 µm, 50 mm) | 340 m / 170 m | 640 m / 320 m | 810 m / 400 m |
| XP50 (17 µm, 50 mm) | 240 m / 120 m | 450 m / 220 m | 570 m / 280 m |
| XQ35 (17 µm, 35 mm) | 170 m / 80 m | 310 m / 160 m | 400 m / 200 m |
Here's the surprise. The XG50, XL50 and LRF XT50 all use 12 µm pixels behind a 50 mm lens, so each pixel covers the same 2.4 cm at 100 m, and their estimates are identical. The higher-resolution models don't see further; they see wider. We explain that in our Telos LRF XT50 review, and the XP50's larger pixels in our XP50 vs XG50 comparison.
What a fox looks like at distance
Picture yourself on a dam bank at dusk, scanning the creek line below. The chart below shows roughly what a fox looks like on screen through a 12 µm Telos at 100, 200 and 300 m.
At 100 m you get ears, tail and posture. At 200 m it's still clearly fox-shaped. By 300 m it's around 10 pixels long, and whether it's a fox or a cat comes down to how it moves. Digital zoom makes the blob bigger on the display, but it can't add pixels the sensor didn't capture, so it doesn't change these estimates.
Why real nights often beat the numbers
The Johnson figures assume a still target and a single look. In the field you have more to go on: how an animal moves, where it is, whether it's with others, and what you saw earlier in the night. With practice, you'll often call a fox further out than 12 pixels would suggest, because a fox trots like a fox.
The opposite also happens. On a humid night when the ground stays warm, contrast drops and every distance shrinks. Rain and fog absorb thermal energy too. That's where the XP50's low NETD helps, even though its pixels are larger. The video at the top of this article, Pulsar's own field footage from the XT50, shows animals across a range of distances.
Our advice: use these figures to set expectations, not as a shooting limit. If your work is mostly foxes inside 200 m, any Telos 50 mm model will do it. If you need to tell pigs apart or call deer past 300 m, choose a 12 µm model.
Choose your Telos
Check the current price and stock on each product page.
Telos XG50 Telos XL50 Telos LRF XT50Telos Identification Range FAQ
How far can a Pulsar Telos identify a fox?
By our estimate using the Johnson criteria, the Telos XG50, XL50 and LRF XT50 identify a fox at about 170 m, the XP50 at about 120 m and the XQ35 at about 80 m. Recognising it as a fox-sized animal roughly doubles those distances. Movement and experience often let you call a fox further out.
How far can a Pulsar Telos identify a pig?
By our estimate, the Telos XG50, XL50 and LRF XT50 identify a pig of about 1.2 × 0.7 m at around 320 m, the XP50 at around 220 m and the XQ35 at around 160 m. Recognition distances are about double. A large boar will be identifiable further out than a small sow or a weaner.
How far can a Pulsar Telos identify a deer?
By our estimate, for a deer of about 1.5 × 0.9 m, the Telos XG50, XL50 and LRF XT50 identify it at around 400 m, the XP50 at around 280 m and the XQ35 at around 200 m. Telling a stag from a hind at those distances depends on antlers and posture, so allow less range for that decision.
What are the Johnson criteria for thermal imaging?
The Johnson criteria are a rule of thumb for how many pixels a target must cover to be seen. In the commonly used form, about 1.5 pixels across the target allow detection, 6 allow recognition of the type of object and 12 allow identification. They assume a still target, so real-world results vary with movement and conditions.
Does digital zoom increase identification range?
No. Digital zoom enlarges the image on the display, but it can't add detail the sensor didn't capture, so the number of pixels on the animal stays the same. It can make a distant animal easier to look at, which helps, but identification range depends on the sensor's pixel pitch and the lens focal length.
Why do the Telos XG50, XL50 and XT50 have the same identification range?
All three use 12 µm pixels behind a 50 mm lens, so each pixel covers the same 2.4 cm at 100 m, by our calculation. A fox lands on the same number of pixels in all three. The XL50 and XT50's extra pixels widen the field of view instead of adding detail on the target.
What target does Pulsar use for its detection range?
Pulsar says its Telos detection ranges are measured against a standard 1.8 × 0.5 m target. By our calculation, at the rated distance that target covers only about three pixels across, enough to notice a heat source but not to tell what it is. Use detection range to compare models, not to judge shooting distance.
Does weather change how far a thermal monocular can identify animals?
Yes. On humid nights, when the ground holds the day's heat, the temperature difference between an animal and its background shrinks, and every distance shrinks with it. Rain and fog absorb thermal energy too. Cold, dry nights give the best contrast. A low-NETD model like the Telos XP50 copes better with low contrast.
Can I identify a fox further away than these estimates?
Often, yes. The Johnson figures assume a still target and a single look. In the field, how an animal moves, where it is and what's around it all help, and with practice you'll often call a fox further out. Always confirm your target and what's beyond it before taking a shot.
Identification and recognition distances are our own estimates using the Johnson criteria and Pulsar's published sensor and lens specifications; animal sizes are typical values.